PVWatts is a solar production calculator from the National Renewable Energy Laboratory (NREL), now the National Laboratory of the Rockies (NLR). Aurora uses PVWatts version 6 when you select it as the engine, or when Auto is selected and any panel isn't connected to an inverter. It uses a simpler, array-level model than the Aurora engine and doesn't simulate individual modules, strings, or inverters.
In this article:
- When Aurora uses PVWatts
- How Aurora runs PVWatts
- PVWatts simulation logs
- Key considerations
- FAQ
- Related articles
When Aurora uses PVWatts
Aurora runs PVWatts when Simulation engine is set to PVWatts v6. In that case, it simulates the whole design with PVWatts.
Aurora also runs PVWatts when Simulation engine is set to Auto and any panel isn't connected to an inverter. In that case, it simulates the whole design with PVWatts, including the connected panels. After the simulation, a warning appears that starts with "Performance simulation warning: Simulated system using PVWatts because modules are not connected to inverters."
To use the Aurora engine, connect every panel to an inverter. See Stringing and Connecting. With Simulation engine set to Aurora, Aurora doesn't switch to PVWatts, and the simulation fails if any panel isn't connected. See Aurora simulation engine.
How Aurora runs PVWatts
- Arrays. Aurora splits the panels into arrays — groups of panels with the same tilt and azimuth — and simulates each array.
- Inverter efficiency. For panels connected to an inverter, PVWatts uses the lowest of the inverter's CEC, European, and maximum efficiencies. For panels that aren't connected, it uses the Inverter efficiency and DC-to-AC ratio in the design's PVWatts settings. Efficiency must be between 90% and 99.5%. Outside that range, Aurora uses 96% and shows a warning.
- Shading and system losses. With Shading engine on, Aurora's shading engine calculates the shading loss. Aurora applies it, along with the design's other system losses, to the output that PVWatts returns.
- Weather data. PVWatts uses the Weather dataset in the design's PVWatts settings, which is separate from the Aurora engine's dataset. See Weather datasets.
PVWatts simulation logs
To open the log, click Production in the summary bar, then Advanced > Simulation logs. A PVWatts log shows:
- The PVWatts version, for example, "Simulating with: PVWatts v6"
- The number of arrays and the weather dataset
- The light-induced degradation (LID) loss used
- For each array, the number of panels, tilt, azimuth, system size, inverter efficiency, DC/AC ratio, panel type, array type, and annual AC output
Aurora applies the shading loss and other system losses after PVWatts calculates each array's annual AC output, so the arrays can add up to more than the design's annual production.
Key considerations
- Shading is a percentage reduction. Because Aurora applies the shading loss to the PVWatts output, shade reduces production proportionally. The Aurora engine models how shade affects each module's electrical output, so it gives a more detailed estimate for partly shaded designs.
- No loss diagram or performance ratio. After a PVWatts simulation, Advanced shows only Simulation logs, and Performance ratio shows 0.00. Both depend on the Aurora engine's loss breakdown.
- Defaults for new designs. New designs get their PVWatts settings from your account's Performance simulations settings. See Performance simulation settings – Account configuration.
FAQ
Why is my PVWatts production different from my Aurora production?
The engines model the system differently. PVWatts uses a simpler array-level model and applies shading as a percentage, while the Aurora engine simulates each module, string, and inverter. Compare designs simulated with the same engine.
Why did I get a warning that my system was simulated using PVWatts?
At least one panel isn't connected to an inverter, and Simulation engine is set to Auto, so Aurora simulated the whole design with PVWatts. Connect every panel to an inverter, then click Simulate system.